Skip to main navigation Skip to main content Skip to page footer

01

Selection criteria

What job should the file belt do?

Start with the material, the existing surface and the intended result: do you need to remove material, deburr an edge, or clean and finish a surface? Then check belt width and length against the belt file and contact arm. The documented VSM KV707T versions differ in dimensions and grade; the nonwoven abrasive on semi-rigid T-polyester follows contours. If a belt is already in use, identify the specific problem – such as service life, access or surface pattern – before choosing another version.

02

FILE BELT RANGE

File belts in the product range

The system listing shows the file belts assigned to this category. Compare versions using the product details for size, grade, backing and intended use.

No products found

No products are currently listed in this category. Request a call back and we will help you find the right product.

Request a callback

03

SELECTION BY APPLICATION

Check the belt, belt file and target finish together

VSM describes KV707T as a nonwoven aluminium oxide abrasive with a full resin bond and semi-rigid T-polyester backing. According to its data sheet, it is suitable for deburring, removing rust, cleaning, removing grinding marks and final surface finishing; the stated pressure is low to medium. Match the grade to the required surface pattern. A nonwoven belt intended for finishing does not replace a different abrasive specified for heavy stock removal.

Fit depends on the machine's specified belt length and width, the contact arm, workpiece geometry and operating conditions. Krückemeyer GmbH converts suitable backed abrasives into belts; material, backing, dimensions and belt joint determine what can be made. Tell us which belt you currently use and what problem you want to solve so that we can assess a suitable belt solution.

04

KV707T DATA SHEET

VSM KV707T file belt data sheet (German) pdf · 718,4 KB View Download

05

FILE BELT QUESTIONS

What is a file belt used for?

A file belt brings abrasive material to contours and hard-to-reach parts of a workpiece. For VSM KV707T, the manufacturer lists deburring, rust removal, cleaning, removal of grinding marks and final finishing. The required result remains decisive: choose a version for heavy stock removal or a defined finish according to its documented purpose. Also describe the workpiece material, geometry and current process so that selection goes beyond the belt name.

How do I choose the grade of a file belt?

Choose the grade according to the starting surface and the desired finish. For VSM KV707T, the manufacturer's data sheet lists grades from coarse to ultra fine and places the material mainly in cleaning, deburring and finishing applications. The appropriate grade depends on how much of the existing surface pattern must be removed and what finish is required afterwards. Check the exact version and test the result on your workpiece.

What file belt size does my machine need?

Belt width and length must fit the belt file and the contact arm in use. The assigned product range includes different sizes of VSM KV707T; this alone does not establish whether a particular version fits. Tell us the machine and contact arm model as well as the size of the belt currently used. We can then check which listed version fits or whether converting to a suitable material and design is possible.

Can Krückemeyer supply file belts in custom dimensions?

Yes. Suitable backed abrasives can be converted into belts with dimensions matched to the application. Whether a particular file belt can be made from the selected raw material depends on the backing, width, length and belt joint, among other factors. The documented belt sizes describe a production range; its limits cannot be combined in every configuration. Tell us the material, machine, required dimensions and application so that we can assess feasibility.

06

Request advice

Describe the material, geometry, initial condition and target finish, along with your belt file and current belt. We will clarify the abrasive, grade, dimensions and possible converting options for your application.

Enquire about a file belt for your application

Send us the workpiece, processing objective and your belt file's dimensions. We will discuss a suitable version and, where needed, assess custom belt converting.

Jürgen Müller

ABRASIVE TECHNOLOGY ADVICE

Jürgen Müller

Contact for products

Jürgen Müller will discuss the material, contour, belt size and required surface pattern with you.

Advice and sales to business customers only!